欢迎访问,东莞市广思远聚氨酯新材料有限公司!
东莞市广思远聚氨酯新材料有限公司
15年专注于PU聚氨酯色膏研发生产
服务热线:

13826972119

当前位置:>广思远资讯> 常见问题
常见问题 公司动态 业界资讯

聚氨酯胺催化剂A-1中英文介绍

点击次数:  更新时间:2021-03-29 10:03:03  【打印此页】  【关闭

聚氨酯胺催化剂A-1

 

胺催化剂A-1主要用于软质聚醚型聚氨酯泡沫塑料的生产,也可用于包装用硬泡。胺催化剂A1对水的催比效力 特别强,因此可使泡沫密度降低。它用于控制产生气体的反应的功效约占80%,用于控制凝胶反应的 功效约占20%。该催化剂活性高,用量少,调节该系列的用量,可控制发泡上升和凝胶时间。胺催化剂A1与有机锡催化剂共用,能使泡沫塑料的生产宽容度明显地提高,确保在生产中不致因操作不小心或计量系统的微小误差导致不必要的质量问题,生产出优质的软质泡沫塑料。 胺催化剂A1被广泛用于制造聚氨酯泡沫塑料的各种配方中,特别适用于生产高回弹、半硬泡和低密度泡沫塑料。

 

物化性能

外观:淡黄色透明液体;

纯度:≥99%;

水分:≤0.5%;

黏度(25℃):4.1mPa.s;

密度(25℃):0.902g/cm3;

闪点(PMCC):74℃;

蒸汽压(20℃):1.3Pa;

沸程:186-226℃

 

供应商

东莞市广思远聚氨酯材料有限公司

 

广思远®更多产品

ZF-10:高效低气味发泡催化剂,典型应用于制备低气味聚氨酯泡沫制品

ZR-50:低气味凝胶催化剂,提供优良的平衡性,可用于聚氨酯模塑高回弹泡沫

Z-131:反应型低气味凝胶胺类催化剂复配剂

Z-130:低气味凝胶催化剂,平衡凝胶/发泡

ZR-70:低气味催化剂,用于包装泡沫和在乙烯基表皮上模塑泡沫发泡和凝胶平衡性好

ZR-40(五甲基二亚丙基二胺):对冷模塑高回弹泡沫特别有效,低气味凝胶和发泡平衡较好的催化剂

LE-310:应用于大块海绵的低气味反应型凝胶催化剂,新型的低VOC胺凝胶催化剂,胺含量超过95%

LE-530:反应型凝胶催化剂,用于各种聚氨酯发泡产品

DPA:低气味凝胶催化剂,突出的平衡性和通用性提供良好的流动性

TAP 1-甲基-4-(2-二甲氨基乙基)哌嗪:卓越的三聚催化剂,可提高流动性

DMDEE(2,2'-二吗啉二乙基醚):强发泡催化剂,提供稳定的预聚物体系

DMAEE:低密度全水硬质泡沫以及低密度半硬质泡沫

BDMAEE 双-(2-二甲氨基乙基)醚:高效发泡催化剂

BDMA(N,N-二甲基苄胺):聚氨酯硬泡催化剂、环氧促进剂

DMEA(N,N'-二甲基乙醇胺):在一些硬泡体系中中和酸,

PMDETA(五甲基二亚乙基三胺):对HCFC/水发泡的硬泡特别有效,类似PC5

 

 

 

Amine catalyst A1

Amine catalyst A1 is mainly used in the production of soft polyether polyurethane foam, and also in the hard foam for packaging. The catalytic effect of amine catalyst A1 on water was particularly strong, so the foam density could be reduced. It controls about 80% of the reactions that produce gases, and about 20% of the reactions that control gels. The catalyst has high activity and low dosage. By adjusting the dosage of this series, the rise of foaming and gelation time can be controlled. The common use of amine catalyst A1 and organotin catalyst can obviously improve the production tolerance of foamed plastics, so as to avoid unnecessary quality problems caused by careless operation or small errors in the measurement system, and to produce high quality soft foamed plastics. Amine catalyst A1 is widely used in various formulations for the manufacture of polyurethane foams, especially for the production of high rebound, semi-rigid foam and low density foams.

 

Physical and chemical properties

Appearance: light yellow transparent liquid;

Purity: 99% or higher;

Moisture: 0.5% or less;

Viscosity (25℃) : 4.1mpa. S;

Density (25℃) : 0.902g/cm3;

Flash point (PMCC) : 74℃;

Vapor pressure (20℃) : 1.3Pa;

Boiling range: 186-226 ℃

友情链接
 - links